Page 27 - PHI - Cierrapuertas

Exit Alarm

Weatherized Exit Alarm
Available for all Apex Series Devices. The Weatherized Exit
Alarm is identical in operation to the standard Exit Alarm but
incorporates a weatherized design for use on a variety of
Exit Alarm applications where contact with the elements may occur.
Available for all Apex Series Devices WALW – Remote Powered
ALK – Battery Operated, provided with a 9 Volt battery and has 12 to 24 VDC at 0.25 Amp., a (2) wire power transfer is required, not
a audible low battery indicator. Specify WH495 Wire Harness for furnished standard. Specify WH495 Wire Harness for Remote Arm/
Remote Arm/Disarm or alternate Input Activation options. Disarm or alternate Input Activation options.
ALW – Remote Powered 12 to 24 VDC at 0.25 Amp., a (2) wire power Weather resistant loss prevention hardware designed for use
transfer is required, not furnished standard. Specify WH495 Wire in outdoor or wet environments:
Harness for External Wire features: • Meets the requirements of MIL-STD 810F, Method 506.4, Driving
• External Arm/Disarm (On/Off) Rain Test (simulating 4 in./hr. rain with 40 mph wind)
• External Activation (to sound Alarm) • Meets the requirements of MIL-STD 810F, Method 509.4, Salt
The Exit Alarm provides a simple way to audibly monitor the Fog test (simulating effects of corrosive environments similar to
use of an exit device. The unit contains a Piezo Alarm which atmospheric conditions found in costal regions)
will sound when the touchbar is depressed. Alarm sounds at 80db To Order: Device with Weatherized Exit Alarm – add suffix “WALW”
at 10 feet. to Device No. (e.g. 2108WALW)
It is also equipped with an LED indicator. The LED flashes GREEN
for 20 seconds when the unit is arming and flashes RED every 20
seconds when the alarm is armed.
Note: Latch Bolt Monitoring (LS) or Door Position Switch (DS) is recommended
when using Alarm option with 2200 Series Surface Vertical Rod devices.
Cylinder
The Exit Alarm requires a standard 1-1/4 Mortise Cylinder (for
cylinder details see page 19) which is used as a key switch to
perform the following functions:
• To turn on (Arm) - it will allow 20 seconds to exit before ......alarm Exit Alarm Kit
sounds. Available for all Apex Devices from 3-0 to 4-0 wide doors. Furnished with
• Silence and reset the alarm after unauthorized egress. Touchbar decal which states:
• To turn off (Disarm) the alarm for continuous unmonitored egress.
• Engage mechanical Dogging for Non-Fire Rated Devices.
Wiring Harness - WH495
Can be wired for one or both of the options listed below. The Exit Alarm is available in Kits for Retrofit on existing devices. The
• Exit Alarm can be turned on (Armed) with alternate inputs. For channel fillers are different lengths for Narrow and Wide Stile devices. “N”
other than our DS880 or NDS986 Door Position Switch a (2) wire denotes Narrow Stile devices.
power transfer hinge is required (furnished by others). To Order: Device with Alarm – add suffix “ALK”, “ALW”
• Exit alarm can be turned on (Armed) or off (Disarmed) from a (e.g. 2108ALK)
remote location. A Cylinder or Dummy Cylinder (by others) is Alarm Kits
required. Cylinders are not furnished standard. Specify when Wide Stile Devices
required (for cylinder details see page 19). A (2) wire power 2-6 & 3-0 ALK-3, ALW-3
transfer is required, not furnished standard.
To Order: specify WH495 4-0 ALK-4, ALW-4
Narrow Stile Devices
3-0 NALK-3, NALW-3
EXTERNAL ARM/DISARM
(ON/OFF) 4-0 NALK-4, NALW-4
(wire colors: Black and Yellow) • WH495 Wiring Harness - Required for External Arming/Disarming the
Alarm and External Activation to sound the Alarm.
EXTERNAL ACTIVATION • Kits are available in finishes 605, 606, 612, 613, 625, 628, ..........
(TO SIGNAL ALARM) 630. For finish description see page 3.
(wire colors: Black and Red)
To order: specify Kit No. and finish (e.g. ALK-3 626).
Note: The Exit Alarm is NOT required when ordering the (DE) Delayed Egress Note: For Battery operated kits a 9 Volt battery is included.
option.

Apex 2000 Series Touchbar Exit Devices 27